THERMOCOUPLE. GRADE. EXTENSION. GRADE. PLUG &. JACK. IEC IEC Intrinsically Safe. BS DIN JIS C NFC T. Kit with a galvanized plate (KSP) for compost probe. Possible fixing with anti-thief device KAV of KISTOCK dataloggers or magnetic fixing of protective housing. IEC. Première édition. First edition. Cou p les therm oé lect riq ues. Troisième partie: Câbles d?extension et de compensation -. Tolérances et sy.
|Published (Last):||18 September 2005|
|PDF File Size:||4.16 Mb|
|ePub File Size:||17.80 Mb|
|Price:||Free* [*Free Regsitration Required]|
Thermocouples are available as separate elements, on one side provided with a thermocouple connector iex on the other side finished with a soldered point and insulation.
The lesser accuracy can than be improved by software.
Thermocouple Color Codes
Measuring a minimal change in theoretical temperature of 0. Programmable calibration procedures A particular advantage of this metal block oven is its ability to execute programmable calibration procedures in iwc with the ValidR validation software. Kec use of type K or type J thermocouples is recommended.
The electronics with the stored calibration data included is dimensioned such that ie standardized measurement accuracy can be guaranteed. For a improved placement and thermal stabilization of the thermocouples during the calibration procedure, it is advisable to make use of so-called thermocouple heating tubes:.
Several individual thermocouples are assembled to thermocouple sets with or without a pressure tight feedthrough. The embedded micorprocessor in TSA 2 communicates digital measurement data with the externally connected personal computer and also processes control commands of the PC for setup and operation of the measurement system.
ANSI and IEC color Codes and limits of error for Thermocouples, Wire and Connectors
A particular advantage of this metal block oven is its ability to execute programmable calibration procedures in combination with the ValidR validation software.
We make a distinction with regard to pressure sensors in accuracy and stability. In order to independently monitor the temperature of the metal block oven MBO during calibration use can be made of a Catch-T model ITCS with pt sensor and iev digital readout:.
But for type T thermocouples additional hardware could be integrated recalibration with resistors.
Other configurations of thermocouple sets are available on request, for example: Sets of thermocouple heating tubes with 6 holes for 6 thermocouples. Individual Thermocouples are available as separate elements, on one side 5884-3 with a thermocouple connector and on the other side finished with a soldered point and insulation.
Our pressure sensors are supplied in adequate housing, equipped with all necessary cabling, power supplies, etc.
For a improved placement and thermal stabilization of the thermocouples during the calibration procedure, it is advisable to make use of so-called thermocouple heating tubes: This pressure sensor is ideally suited for measuring the vessel pressure jec steam sterilization processes: The most well known use is in the IAVS-M2 systems see below for detailswhich provides the interface between the measuring sensors and the software in a portable computer, which registers and records the measurements in charts and tables.
A change in temperature of 0. For these types linearisation hardware is standard available ICresulting in a situation with high accuracy. Moreover there is also the possibility of connecting your own separate pressure sensor. The scanner comes including: Each analog thermocouple signal is converted to digital signal at a precision of 16 bits; in this range this means a real accuracy of at least 0.
In combination with the TSA2, the metal block oven has the following properties: Thermocouple sets Thermocouple sets are fitted: Type and the length are at your choise. For the metal block oven option, in combination with the thermocouple calibration facility, an accuracy of 0. After a one-time setup of the desired calibration points up to 10 points are allowed iecc, they are automatically run through under the control of the TSA2 and ValidR.
Iec Download .pdf
By means of this integrated functionality, the entire calibration procedure can be carried out independently and unattended. This pressure sensing system has a range of 0 to kPa and an accuracy of 0.
It is also possible to enter a desired point of time at which the calibration procedure is then started automatically. Due to the temperature compensation the accuracy stability can be guaranteed for at least a year, so a 1 x annual calibration can suffice.
Miscellaneous A pressure sensor is supplied with a calibration certificate traceable to international standards.
For example, two pressure sensors can have the same accuracy, but the stability, among other things as a result of temperature variations of one of the two pressure sensors, may be such that the accuracy can not be guaranteed over a longer period of time.