Find great deals for Haas Sl CNC Lathe. Shop with confidence on eBay!. Large selection of second-hand Haas SL available here. Great offers from top traders & auctions all in one place. Buy your Haas SL today!. Productivity Inc – Haas CNC Lathe Operator Manual. Page 1. Haas Lathe Operator Training Manual. Table of Haas VMC (SL) showing the X and Z axis.

Author: Mebei JoJoshicage
Country: Netherlands
Language: English (Spanish)
Genre: Automotive
Published (Last): 25 September 2005
Pages: 466
PDF File Size: 9.93 Mb
ePub File Size: 9.99 Mb
ISBN: 271-8-53463-975-3
Downloads: 31827
Price: Free* [*Free Regsitration Required]
Uploader: Taurg

It comes complete with a 12 tool-station turret, hydraulic chuck, Toolsetter, chip conveyor, parts catcher, rigid tapping, tool holders and bar feed interface. Water xl10 Your Air System? Complete a simple form and your local Haas Factory Outlet dealer will contact you.

Haas Sl CNC Lathe | eBay

TC Cam Lever 8. Most big websites do this too. Axis rotating slowly, hesitating to rotate. Find videos, highlights and features of new products coming off the engineering pipeline. Test the air cylinder for faulty piston seal.

If air is escaping from the upper hose unclamp connection on the cylinder the cylinder piston seal is bad and piston should be replaced.

Go to DIY servo system trouble shooting. Mercuriusstraat 28 B Zaventem, Belgium Phone: Please fill in a valid e-mail address! Turret Mount Coupling You have successfully subscribed.


Check the incoming air supply. Check the turret unclamp sl110. CALM System All solenoids located in the lube panel Use needle tipped probes and take care not to touch probes tips together when checking voltage. No matching alarm was found for the given alarm code. Remove the left rear machine enclosure panel. By entering and confirming your email address, you will receive an e-mail notification as soon as new offers are received for your search.

In MDI command an M43 and press cycle start to unclamp the turret. Y axis motor thrust: The lathe has a 12 tool station turret with an X standard axis. Make sure a minimum 1″ 25 mm space is between the turret and all objects in the direction of the Z Axis. If you cannot turn the coupler ssl10 your hand, use a flat-head screwdriver to turn the coupler.

The turret unclamp sensor is faulty or out of adjustment.

HAAS SL with BARFEED, CNC Turning Center

Turret Unclamp Sensor Please click the link in the email we just sent you, to complete the subscription process. Haas SL Rate this product!

Check the turret unclamp and clamp sensors. This aligns the electronic zero channel with the mechanical home switch position and clamps the turret.

The Haas Resource Center

In this case the turret should be removed to clear the chips and inspect for possible damage. Using M43, Unclamp the turret. If the sensors were activated then they may need to be adjusted. Select by Model Type Indexers. Measure the voltage at the solenoid power connection. If the magnet did not activate the sensors inspect the cables. Ahas noise as the turret rotates Tool Turret Die springs are broken.


Male Turret Coupling Use needle tipped probes and take care not to touch probes tips together when checking voltage. Air Cylinder Assembly If there is no voltage, refer to: Haae reload the page and try again.

To confirm your subscription, click hqas link, we’ve sent you by mail. Check turret for possible turret o-ring damage or chip intrusion. Remove lock out tags, power up and zero return the machine. Make corrections as needed. Remove the rear cover [1]. View Privacy and Cookie Policy.

Align the coolant nozzle with the coolant port, as shown. To make this site work properly, we sometimes place small data files called haaw on your device.