I would like to get a very nice trigger job on a SS GP for the single Ruger forum I found the IBOK for the GP on Google (GP IBOK). I received the GP pdf this morning. I found the IBOK so helpful thought I should bump it back up so others could keep seeing it. Gp Ibok – PDF Free. Download – -. Ruger sp manual pdf ruger sp manual pdf magnum revolver like the. Ruger GP For many.

Author: Gak Mole
Country: Burkina Faso
Language: English (Spanish)
Genre: Spiritual
Published (Last): 7 September 2005
Pages: 322
PDF File Size: 15.45 Mb
ePub File Size: 11.34 Mb
ISBN: 657-8-47920-534-6
Downloads: 30864
Price: Free* [*Free Regsitration Required]
Uploader: Megal

It must be very smooth. Along the lines of Sixto’s suggestion, if I recall correctly the trigger group of the GP removes tp100 easily – no sideplates to tap off, etc.

With spring-powered devices such as a hammer, you can reduce mass in non-critical areas and increase hammer velocity considerably. Yea, I do it with my semis and its part of why I like them. Remove the trigger guard assembly and measure the side play between the one side of the trigger and the strut. All the options you have as far as making and shooting different loads and powder charges without having to think about a malfunction is what makes me like them so much.

I have one of my own in 4″.

You can open the throats to. In this case, a gunsmith is highly recommended. Pull the blade to the left with your thumbnail until the right side of the blade drops in.

It’s all I use on my Stainless Steel weapons. Ruger, on the other hand I took my speed six and SP same basic designs as the GP down to the bare bones and cleaned each part then applied Eezox iboi buffed it all once it was dry.

  AS NZS 2890.1 PDF

Reassembly of the trigger guard assembly: Ease the ivok up to release spring tension. Use a kitchen fork and place the tines of the fork in the spring coils near the seat. Pull the trigger and ease the hammer down.

A coil spring part 12 is installed between the collar on the firing pin and the recoil plate. Iowegan, thank you very much for the PDF’s.

Fire lapping products are not recommended. Send a private message to Big Andy The previous poster didn’t mean for you to clean the outside of the gun. It was and is very kind of him to allow me to republish it!

Strange problem with my GP

Their revolvers are due for the same type of improvement. Also, remove any machine marks from the bottom surface and buff it smooth. If I missed the reference my appologies. It really felt like Ruger didn’t put much attention to detail in this revolver at all.

And you don’t have to bend over to pick up your brass, you can just dump ubok into a bag on your shooting bench: I ended up getting it to fire by tipping the gun upward and then lowering it to the level position.

Since youbought it used, I would call ruger or wolff and get a stock hammer spring. I am going to call my brother now.

Much like the trigger, you will usually see about. I knew I iboi like it more after fine tuning it but the gun turned out even better than I expected. The front sights are very easy to change and the HiViz front sights come with red and green tubes and a couple of spares.


New GP – Survivalist Forum

February 25th, Lighten up and enjoy life because: Does anybody have any success stories out there? I started the blog because I found so much misinformation and just poor info I decided I would put as much info on the blog as I could after making sure of my sources plus my own experience over the years. Once the left panel is pushed out, a small disassembly pin part iobk will drop out.

It will not fail at all now. Once the trigger plunger is in position, insert the trigger into the trigger guard frame making sure the spring strut is in the trigger spring hole.

GP100 IBOK for SP101

To remove the rear sight blade, turn the windage screw counter-clockwise until the right edge of the sight blade is flush with the sight base. You have no idea how great that makes me feel that you think so highly of my blog. Normally, there will be about. It happened again, after approx. Release the trigger guard latch part 43 and pull it out. I started this blog to help fellow shooters with good accurate unbiased information and that makes it well worth writing when someone like yourself finds it useful.