This tutorial is intended to give basic instruction on how to setup and run a Note: FloXpress will not work if the Flow Simulation add-in is currently installed. Solidworks FloXpress is a feature inside Solidworks that allows a designer simulate flow of fluids through a model. Based on the results of the. This simple tutorial is designed to show you the process of solidworks floxpress. The part that we use here is a simple part because our main goal is the process.
|Published (Last):||23 February 2008|
|PDF File Size:||7.16 Mb|
|ePub File Size:||15.14 Mb|
|Price:||Free* [*Free Regsitration Required]|
Home solidworks tutorial ebooks solidworks 3d sketch-1 solidworks sheetmetal-1 solidworks loft-1 solidworks flowxpress-1 solidworks photoworks-1 solidworks motionstudy solidworks drawing The velocity chart illustrates the flow speed during the processthe colors are observable in the flow. From the report we can obtain properties such as maximum flow velocity.
This free tool allows you to calculate how fluid or air flows through a part or assembly document. This was a very simple flow analysis.
All of these articles will be stored in the category of Daily Dose…. June 17, by Chris Taylor. From the results window you can simulate the trajectory of fluid particles tutoria they move through the model.
solidworks tutorial flowxpress #1
A sample report is like the one shown below. The part that we use here is a simple part because our main goal is the process of floxpress. The boundary conditions are also clearly described in the floxpgess. Solidworks FloXpress is a feature inside Solidworks that allows a designer simulate flow of fluids through a model.
Tutorial – Using FloXpress in Solidworks?
In the fluids windowselect water and click next. Next we define the inlet boundary conditions. Home Support Daily Dose Trajectories are tangent to the flow velocity at every point. Contact us for more information and buying SolidWorks at support nccs.
SWA home about contact us. Once a pressure is selected, you can ffloxpress the analysis to calculate flow velocity. Menu Home solidworks tutorial ebooks solidworks 3d sketch-1 solidworks sheetmetal-1 solidworks loft-1 solidworks flowxpress-1 solidworks photoworks-1 solidworks motionstudy solidworks drawing-1 solidworks 3d-sketch-2 solidworks assembly-1 solidworks loft-2 solidworks 3d-sketch-3 solidworks loft-3 solidworks assembly-2 solidworks surface-1 solidworks surface-2 floxprss sheetmetal-2 solidworks assembly-3 solidworks simulation-1 solidworks advanced loft solidworks drawing 2 solidworks toolbox solidworks pattern solidworks floxxpress 3 solidworks simulation 2 solidworks helix.
Click next and then click solve and wait. This simple tutorial is designed to show you the process of solidworks floxpress. Define a plane parallel to the end face of the part and set the mm offset distance. We are here to close the two ends of the part so insert a new part just like below:. A Microsoft Word report can be generated. The analysis is based on the calculated velocity field. Use this information in conjunction with experimental data and practical experience. Click on the next button again.
Now the part is ready. Home solidworks tutorial ebooks solidworks flowxpress Now the part1 is added to design tree. The FloXpress wizard has a procedural sequence that enables the user maneuver through the simulation with ease and comprehensively understand the simulation.
The next step is to solve the model. Once the geometry is valid, you next select water or air as the fluid for the calculation.
I will make sure that my future students have the links to read this themselves. As you can see in the message box, the model is not ready for flow analysis.
Click on the next button in welcome message. Once we have created the lids we can then proceed to begin the simulation. Right click on it and select edit part:. Based on the results of the simulation the designer. A new assembly opens, the begin assembly window appears with your part ready to insert, just click on the working area and your part will insert there. The first step is to ensure that the model has no openings fully closed with lids.
So right click on main part and select appearance. Next we choose the fluid that would flow through the model. For the sake of keeping this tutorial short I leave it to you. Now there is a lid on one side. This simulations can be done using either pipes or bubbles. The opening must be closed with lids. Field testing is mandatory to validate your final design.
Excellent help tutorials with your Free Tugorial Utilities series. The check geometry window appears which indicates the smallest passage. Close the check geometry window. Do the same for the other side and we will be ready for floxpress. The Solidworks FloXpress icon is located under the evaluate tab.