EV CPS2.9 PDF

Designed for the contractor, the CPS MK II feature 2-RU chassis, Phoenix-type connectors for inputs and outputs, pre-programmable power-on delay, easy power-on via remote contact closures, rear panel attenuators, and a switchable 50 Hz high-pass filter. Like the CPS multi. Two-Channel Models CPS, CPS, CPS, and CPS CPS2.x rear view. Remote power-on contact. 1. Programmable power-on timer. 2. Module slot for. Buy Electro-Voice CPS 2-Channel Power Amplifier for RCM IRIS-Net Remote Control Module (W, 4 Ohms) Review Electro-Voice CPS

Author: Dogal Kagabar
Country: Yemen
Language: English (Spanish)
Genre: Technology
Published (Last): 1 February 2006
Pages: 245
PDF File Size: 15.64 Mb
ePub File Size: 9.21 Mb
ISBN: 920-3-86589-987-4
Downloads: 29940
Price: Free* [*Free Regsitration Required]
Uploader: Yorr

Do not use the power amplifier near heat sources, like heater blowers, stoves or any other heat radiating devices.

Electro Voice EV CPS Amplifier

Extremely high voltages can be present at the output. This indicates all protections are working fine. Only the provided power cord may be used. Page of 24 Go. Attach the power amp with its frontal rack mount ears using 4 screws and washers as shown in following illustration.

Controls, Indicators and Connections Front View 1. Set the cs2.9 to the 50 Hz position for activating the High Pass Filter. Mains Switch Rear View 1. Mounting CPS amplifiers have been designed for installation in a conventional inch rack case. Show all Contractor precision cps2. Keep ventilation louvers free from dust to ensure unhindered airflow.

Turning the Mains Switch to ON starts booting up the power amp. Inputs are electronically balanced. For eg options and packages, contact us at Connect the power amplifier only to a mains network, which corresponds to the requirements indicated on the type plate. Unbalanced connections should only be used if the cables are very short and no interfering signals are to be expected in the vicinity of the power amplifier.

  KARD ES MEGADATIK PDF

Electro Voice

This mode of operation is being used for all 2-channel applications, like stereo operation. Whenever possible, using balanced audio signal feeds at the input of the power amplifier is always preferred. Due to their immunity against external interference sources, such as dimmers, mains connections, HF-control lines, etc. For fixed amplifier installations in a device control room that incorporate a central air-cooling system or air conditioners, calculating the maximum heat emission may be necessary.

Keep ventilati- on louvers free from dust to ensure unhindered airflow. By pressing ‘print’ button you will print only current page. The terminals marked with are hazardous live and the external wiring connected to these terminals requires installation by an instructed person or the use of ready-made leads of cords.

Do not use the power amplifier near heat sources, like heater blowers, stoves or any other heat radiating devices. In DUAL mode, the two channels of the power amplifier work independent from each other. In general, setting up or mounting the power amplifier has to be done in a way that fresh air can enter unhindered at the front and exhausted air can exit at the rear.

This manual also for: Electrovoice compact precision cps: Electrovoice contractor precision cps1: This mode of operation is being used for all 2-channel applications, like stereo operation.

Also See for CPS2.

The difference between power consumption and dispensed power is called power dissipation P d. Please also see following illustration. The power cs2.9 remains cooler and dissipating the developing waste heat in a specific direction gets easier.

Otherwise, a 6 dB drop in level could result. Attach the power amp as shown in the illustration using 4 case nuts and screws. As with all Electro-Voice power amps with fan cooling, the airflow direction is front-to-rear, obviously because there is more cold air outside of the rack case than inside.

  AUSTIN COATES RIZAL PDF

CPS amplifiers have been designed for installation in a conventional inch rack case. The Mains Switch on the front panel separates the power amp from the mains.

Electro-voice CPS Manuals

The connected speaker systems must be able to handle such voltages. Don’t show me this message again. Speaker system switch-on is delayed by approximately 2 seconds via output relays, effectively suppressing any possible power-on noise, which otherwise might be heard through the loudspeakers. Do not modify this unit!

Electrovoice contractor precision cps2t: Amplification is set via input level control of channel 1 only. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintance servicing instructions in the To print the manual completely, please, download it. Please take time to consult this manual so that you can understand all the features built into your Electro-Voice amplifier and fully utilize all its performance capabilities.

Electro-Voice Cps2.9 MKII Contractor Class-h Power Amp 2×900 Watts

Brackets for securing the power amplifier are available as accessories. Make sure to completely read and fully observe power rating specifications cpz2.9 the speaker systems to be used and to check them against the output power capacity of the power amp.

The correct connection is also indicated at the amplifiers rear panel. Comments to this Manuals Your Name.