When looking for a used DECKEL FP1 for sale, it is helpful to make sure that the instructions manual and operating instructions, the data sheet spec are also. New electical cabinet with emergencystop. Safety hood with electrical switch. Collets with sleeve S20x2 Drill chuck. Some toolholders and tooling. Add to cart.
|Published (Last):||19 May 2016|
|PDF File Size:||9.14 Mb|
|ePub File Size:||4.86 Mb|
|Price:||Free* [*Free Regsitration Required]|
Checks were also made using the dummy shaft, DTI and straight edge shown in my last post. For the cost of transportation of a DECKEL knowing weight and dimensions is essential, independent of the year of manufacturing.
I know what it and a FP4 can do but not an FP1. The results were impressive so much that until approximately 50, copies of the FP1 milling machine were sold. General Layout Constructed in an ingenious way, the layout of the spindle-drive system was both compact and effective: Login to Decckel Account. For spiral milling the workpiece has to be both continuously rotated and moved axially beneath the cutter, the two moments being co-ordinated in the correct mathematical sense for the job in hand.
Esslingerstrasse 7, Oetwil am See, CH. Table feed direction-control lever. F;1, Germany dealership location. FP-1, and if you need more oooomph, then suplement it.
Rebuilding an old Deckel FP1
Obviously the travels are shorter. You could switch an FP-1 from horizontal dec,el vertical 5 times in the span that you could mount a right angle head and support on a BP, and often you can leave a horizontal cutter in the horizontal spindle while still using the vertical head I see this a lotwhich allows you two operations in one setup. I’m trying to figure out whether to sell my B-port for ddckel and money for a new mill You have successfully subscribed.
A short-travel, spring-loaded quill was fitted to help with light drilling dwckel tapping operations. Results 1 to 20 of Available 6 months after delivery, on the mechanics of us partially reconditioned single-layered. How much should a good but not excellent condition FP2 in California with a swivel table but no other tooling, approx early s 40int spindles go for.
Toolroom milling machine Deckel FP1 2102 Active
To distinguish these models from the later types that are now very common, often referred to as “Type F0”. Check the dcekel of the dealer.
What other tooling was available for an FP4? The spindle carrier assembly could be rotated through degrees about its vertical axis, whilst the cutter-spindle proper could be twisted through an angle of 90 degrees. The motor, mounted on the back of the machine on an exposed platform, can easily be changed.
You comments would be appreciated. John, I think the problem might be that your photo albums are not “visible” to others.
▷ Used Deckel Fp1 for sale – Machineseeker
All the heads could be driven backwards and forwards across the top of the main column to provide an in-out veckel, while the tables bolted to a flat, vertical T-slotted table equipped with power longitudinal and vertical feeds. If not, you will probably make money on what you invested as they dp1 to be going up in value. You can create a label. Of course occur anyway during the purchase process differences of opinion. A friend of mine did that, and it was quite neat.
Coarse setting of the head was made by hand against a graduated scale, whilst fine adjustment was through worm gearing against gauge blocks and dial-indicator readings. The head could be swivelled 45 degrees either side of central. Toolroom milling machine Deckel FP1 Active. The list goes on and on. Universal milling machine manufacturer: This could be set by the operator to give 8 speeds in one direction or 4 forwards and 4 reverse.
Should you come across any deciel these makes and models all will provide “The Deckel Experience” – though you must bear in mind that spares are unlikely to be available and, being complex, finely-made mechanisms, they can be difficult and expensive to repair. As part of this rebuild the machine was fitted with a roller bearing horizontal spindle and an Alexander vertical head and slotting attachment.
Results were impressive with, bysome 50, examples of the FP1 having deckell produced, together with many thousands of different models. Emco Model F3 Belgium: Save the extra bux and do it right.