ASTM D5587 PDF

Tear test of Fabric by trapezoid method to ASTM D ASTM D covers the measurement of the tearing strength of textile fabrics by the trapezoid tear test using a constant-rate-of-extension-type (CRE) tensile. ASTM D Tearing Strength of Fabric by. Trapezoid Procedure. • Scope – this test method describes the determination of the tearing strength of fabrics by the.

Author: Dokus Mahn
Country: Eritrea
Language: English (Spanish)
Genre: History
Published (Last): 10 July 2012
Pages: 136
PDF File Size: 11.55 Mb
ePub File Size: 15.27 Mb
ISBN: 436-3-85815-120-7
Downloads: 56937
Price: Free* [*Free Regsitration Required]
Uploader: Mezijar

Force range of 5 kN to kN 1, lbf tolbf Adjustable test space The most popular choice for static tension and compression tests These dual column testers are available in both tabletop and floor standing models.

The American Society for Testing and Materials takes no ast, respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

Hold the short edge taut, and let the remaining fabric lie in folds. The highest peaks appear to reflect the strength of the yarn components, individually or in combination, needed to stop a tear in fabrics of the same construction.

The values stated in inch-pound units may be approximate.

Stop the crosshead motion asrm a total tear of approximately 75 mm 3 in. If a bias astk found, either its cause must be found and corrected, or the purchaser and the supplier must agree to interpret future test results with consideration to the known bias. Consequently, these test instruments may be used when agreed upon between the purchaser and the supplier. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Individual reprints single or multiple copies of this standard may be obtained by contacting Atsm at the above address or at phonefaxor service astm.

Signicance and Use 5. Description Literature Contact Us This standard mainly applies to most woven textile fabrics, but can be applicable to fabrics produced by other techniques. Competent statistical assistance is recommended for the investigation of bias. Mark each specimen with an isosceles trapezoid template see Figs. This standard mainly applies to most woven textile fabrics, but can ashm applicable to fabrics produced by other techniques.

  L5R RPG THE GREAT CLANS PDF

ASTM D – 05 Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure

Perform the test within 2 min after removal of the specimen from the water. Please confirm that you agree with our privacy and cookies policy to submit this form. It is recognized that some constant-rate-of-traversetype CRT tensile asmt machines continue to be used. The average results from the two laboratories should be compared using the appropriate statistical analysis and an acceptable probability level chosen by the two parties before testing is begun.

Larger differences are likely to occur under all other circumstances. A number in parentheses indicates the year of last reapproval. Bluehill Universal Software is built from the ground-up for touch interaction astn an intuitive user experience. The nonparallel sides of the marked trapezoid are clamped in parallel jaws of a tensile testing machine.

Subscribe to Our Newsletters. In any event, the CRE-type machine shall prevail. In some cases, due to fabric constructions, individual yarns may not rupture but show a high peak and yarn distortion asym the test specimen. Glossary of Materials Testing Terms. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn.

Consequently, these two tensile testers cannot be used interchangeably unless the degree of quantitative correlation has been established between the purchaser and the supplier. awtm

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Instructions are sstm for testing specimens with or without wetting. Email addresses must contain the symbol. In any event, the CRE-type machine shall prevail.

Tear Strength of Fabrics – Trapezoid Procedure

Pneumatic side action grips with rubber coated jaw faces are well suited for clamping of the trapezoid specimens. If bias is found, either its cause must be found and corrected, or future aatm results for that material must be adjusted in consideration of the known bias.

Typically for woven fabrics, if a small decrease in force occurs at a time d5857 the force is increasing, it is not considered to peak unless the indicated force exceeds the force required to break a yarn.

  ATOM PHOTON INTERACTIONS COHEN TANNOUDJI PDF

By continuing to use our site, you accept our cookie policy. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part d55877 the standard. When specimens are to be tested wet, take the specimens from areas adjacent to the dry test specimens. We use cookies to improve your browsing experience.

Take the specimens to be used for the measurement of the cross-machine direction with the longer dimension parallel to the crossmachine direction. For fabrics not readily wet out with water, such as those treated with waterrepellent or water-resistant materials, add a 0.

Make a preliminary cut 15 mm 0. The fabrics may be untreated, heavily sized, coated, resin-treated, or otherwise treated. In the absence of such an agreement, take the number of fabric rolls specied in Table 1. It is the responsibility of the user of this standard to establish atm safety and health practices and determine the applicability of regulatory limitations prior to use.

There were sufficient differences related to the fabric type and structure to warrant listing the components of variance and the critical differences separately. Link to Active This link will always route to the current Active version of the standard. Contact Us View Accessories Catalog. The satm for use of the CRT-type tensile tester are included in.

ASTM D covers the measurement of the tearing strength of textile fabrics by the trapezoid tear test using a constant-rate-of-extension-type CRE tensile testing machine. Avoid getting oil, water, grease, and so forth, on the specimens when handling. Preparation of Test Apparatus and Calibration 8. Adjustable grip pressure also allows users to fine-tune the gripping pressure to atsm jaw breaks or slippage.