ASTM DENGL I 0b3b | This standard is issued under the fixed designation D ; the number immediately following the. This standard is issued under the fixed designation D ; the number immediately 1 This test method is under the jurisdiction of ASTM Committee D10 on. The ASTM-D standard test method for drop test of loaded containers evaluates the capability of a container to withstand the sudden shock resulting from a.
|Published (Last):||25 June 2006|
|PDF File Size:||20.72 Mb|
|ePub File Size:||14.62 Mb|
|Price:||Free* [*Free Regsitration Required]|
This test method forms part of almost all inspections. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
ASTM D – 98() Standard Test Method for Drop Test of Loaded Containers by Free Fall
Link to Active This link will always route to the current Active version of the standard. These ISO standards may describe procedures that do not meet the requirements for this test method. The height of each drop is thus determined by the result of the previous test. This procedure determines the number of drops or cycles required to damage the package or contents. It is e5276 responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
This test method may also be used to compare the performance of different package designs. Research Report Adtm describes an interlaboratory test program of three packaged items, aetm drop heights to failure. The values given in parentheses are mathematical conversions to SI units that are asttm for information only and are not considered standard. NOTE 1—Grout a thin mortar used to? Standard Test Method f The mean drop heights to failure for the three types of packaging were 39, Quality control inspection companies often simply refer to it as the carton drop test.
Regardless of which procedure is used, close the container in the same manner that will be used in preparing it for shipment.
Replicate samples should be subjected to identical procedues to determine the consistency of the failure point. Why perform a drop test of loaded containers? This test method may also be used to compare the performance of different package designs.
Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
The number of test specimens depends on the purpose sstm the tests but will usually require eleven or more replicate test specimens; using much larger sample sizes will result in higher con? Where it is desirable to drop on a midpoint between two locations on the chime, such a point can be designated using two numbers, that is, drop on GPO,Chapter These ISO standards may describe procedures that do not meet the requirements for this test method.
Where a bag or sack has one or astn side seams, Side 2 shall include a side seam.
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. D — 98 A2. The values given in parentheses are for information only. See Practice D for ashm guidance.
ASTM D standar Get to know us! ASTM D — 98 is a standard test method for drop test d527 loaded containers cartons by free fall. If this specimen passes at this drop height, the next test will be at a higher drop height with a new package.
D Terminology of Packaging and Distribution Environments. Notify me by email when the comment gets approved.
A superscript epsilon e indicates an editorial change since the last revision or reapproval. Download our Quality Control Essentials Download.
The atm height shall be measured from the top of the timber. When the capability of a container to withstand rough handling is to be evaluated, pack the container with either the actual contents or a load simulating the contents.
Drop test of loaded containers (cartons), ASTM D5276
The determination of the critical orientation must be provided. ASTM-D wstm particularly suitable for containers that are normally handled manually during some part of their distribution cycle. It is best to choose an odd number of test specimens.
It is common to estimate the critical drop height as ashm midpoint between the last successful test and the test which caused damage; use of the successful test point before failure may be considered a more conservative estimate.
If drop leaves are used, the apparatus shall provide a spring or other mechanism so that the leaves do not interfere with a free, unobstructed fall.
This test method may also permit observation of the progressive failure of a container and the damage to its contents.
Inspection Process View All. This xstm method may also permit observation of the progressive failure of a container and the damage to its contents. Historical Version s – view previous versions of standard.
ASTM-D – Medical Package Testing
Where it is desirable to drop on a midpoint between two locations on the sidewall, such a point can be designated using four numbers, that is, drop on The ASTM-D standard test method for drop test of loaded containers evaluates the capability of a container to withstand the sudden shock resulting from a free fall, or the capability of a container and its inner packing to protect its contents d5267 the sudden shock resulting from a free fall.
The use of a log-normal distribution is often suggested but this requires the drop height increment to be a constant based on the logarithms of the drop height, thus the actual drop height increment would change with the drop height.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.