ASTM D3389 PDF

This standard is issued under the fixed designation D ; the number 1 This test method is under the jurisdiction of ASTM Committee D on Rubber. ASTM D is an abrasion method used for coated materials and is cited for classification testing by the ANSI standard. ASTM D Abrasion resistance tests are intended to measure the wear resistance properties of a material. This may be correlated to expected end use.

Author: Nalar Nisho
Country: Norway
Language: English (Spanish)
Genre: Health and Food
Published (Last): 7 July 2017
Pages: 74
PDF File Size: 14.25 Mb
ePub File Size: 1.73 Mb
ISBN: 308-8-23676-351-5
Downloads: 51035
Price: Free* [*Free Regsitration Required]
Uploader: Mikazuru

This guide is intended to assist in establishing procedures for determining the relative resistance of treated or untreated mortar surfaces. This method specifies the testing methods for determination of zstm resistance of rubber, vulcanized or thermoplastic hereafter referred to as “vulcanized rubber”.

This standard specifies requirements for glazing materials for use in motor vehicles and motor vehicle equipment. NASTA Manufacturing Standards and Specifications for Textbooks If offset printed on coated cover material, a protective top coating for abrasion resistance is required. This norm specifies a method for the determination zstm resistance to abrasion for paints, varnishes ast, products when using the Taber Abraser.

Determination of whether the plastic, safety glazing material has a certain minimum resistance to abrasion at ambient temperature under dry or wet car wash conditions.

Taber Test Methods: Taber Abraser (Abrader) – Taber Industries

This specification covers minimum material performance and laboratory test procedures for non-reinforced liquid coating encapsulation products single or multiple-coat systems for leaded paint in buildings.

The number of revolutions of the specimen required to cause a defined degrees of abrasion is used as measures of resistance to abrasion.

This specification covers a catalyzed epoxy system of marking inks for metallic or other non-porous surfaces. This standard describes a method for the determination of the abrasion resistance of organic flooring materials when exposed to walking traffic of a revolving nature point abrasion. Accordingly, specifiers should consider the following qualifiers when assessing double rub ratings: This test method covers the determination of the loss of pile, specifically pile pull out, due to abrasion.

  IBM HOLEY OPTOCHIP PDF

satm This test measures the ability of the surface of high-pressure decorative laminate to resist abrasive wear-through of the decorative layer. Applications of high pressure decorative laminates covered by this Standard include wait stations, d33899 counters, and other counters when used in conjunction with cutting boards or other means of preventing direct food contact with the laminate.

ASTM E Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings This specification covers minimum material performance and laboratory test procedures for non-reinforced liquid coating encapsulation products single or multiple-coat systems for leaded paint in buildings.

The purpose aatm this test is to determine the extent of magnetic stripe abrasion resistance. The number of cycles that the fabric can endure before fabric shows objectionable change in appearance yarn breaks, pilling, holes is counted. Where more than one test method is listed for the same characteristic, no attempt is made to indicate superiority of one method over another.

This d3389 establishes the engineering requirements for producing a hard anodic coating on aluminum and aluminum alloys and the properties of such coating.

This commercial item description covers the requirements for a structural fireman’s coverall to be ast by Navy damage control fire fighters. ISO Specifications for Hard Anodic Oxidation Coatings on Aluminum and its Alloys This International Standard specifies requirements for hard anodic oxidation coatings on aluminum and its alloys, including test methods.

This method covers the selection criteria for hand protection systems including chemical permeation, puncture resistance, and abrasion resistance. A fabric with twice the number of abrasion cycles does not indicate double the service life. EN Wood flooring – Test methods to determine elasticity and resistance to wear and impact resistance This document specifies two alternative test methods to determine the resistance to wear of lacquered wood floorings and one method to test the elasticity of the lacquer.

Standard Test Method for Coated Fabrics Abrasion Resistance (Rotary Platform Abrader)

It does not apply to industrial kitchen sinks. This is an oscillating test.

  JOHN SMITH GENERALL HISTORIE OF VIRGINIA PDF

The test shall be used to give an indication of the comparative wear characteristics of painted, printed or hot embossed finishes, to d33389 substrates. CID A-A Gear, Fire Protective This commercial item description covers the requirements for a structural fireman’s coverall to be used by Navy damage control fire fighters. Rotary Platform, Double-Head Taber Method This method is intended for determining the abrasion resistance of cloths in terms of percent change in breaking strength, or breaking strength after a given period of abrasion, or the number of abrasion cycles required to produce a specified state of destruction.

This document covers insulated, flexible air duct assemblies for portable ground support air conditioners and heaters.

DIN and Taber 5155 Abrasion

ACT reminds you that there are many points to v3389 when specifying textiles. This specification covers the requirements for photosensitive anodized aluminum sheets and foils. This test method covers determination of abrasion resistance, fiber loss and bearding resistance of automotive carpet materials.

This specification covers requirements for electrolytically formed oxide coatings on magnesium and magnesium alloy parts where appearance, abrasion resistance, and ast against corrosion are important. Testing Methods This method specifies the testing methods for determination of abrasion resistance of rubber, vulcanized or thermoplastic hereafter referred to as “vulcanized rubber”.

Understanding Abrasion Testing – Alendel Fabrics Ltd.

This document sets forth recommended minimum performance standards for vinyl and other polymeric films, plain and printed, which are used as in-ground swimming pool liners. This c3389 covers the requirements for six types and two classes of electrolytically formed anodic coatings on aluminum and aluminum alloys for non-architectural applications.

Association of Contact Textiles Website.