ASTM B153 PDF

B – 11 Standard Test Method for Expansion (Pin Test) of Copper and Copper- Alloy Pipe and Tubing, copper, copper alloy, expansion, expansion test, pin. This standard is issued under the fixed designation B ; the 1 This test method is under the jurisdiction of ASTM Committee B05 on Copper. Find the most up-to-date version of ASTM B at Engineering

Author: Mizragore Mur
Country: Mauritania
Language: English (Spanish)
Genre: Sex
Published (Last): 21 October 2013
Pages: 478
PDF File Size: 6.13 Mb
ePub File Size: 13.76 Mb
ISBN: 408-4-69682-195-6
Downloads: 32241
Price: Free* [*Free Regsitration Required]
Uploader: Kagalmaran

The purchaser shall have the option to specify either a hydrostatic test in The manufacturer shall select the nondestructive test that is most suitable for the tube size and the application.

For all other tube no Rockwell hardness values shall apply. However, if subsequent testing by the purchaser establishes that the material does not meet these requirements, the material shall be subject to rejection.

Hard-drawn temper is used bb153 where there is need for a tube as strong as is commercially feasible for the sizes indicated. The notchdepth tolerance shall be Standard Specification for Gray Iron Castings.

List of ASTM International standards – Wikipedia

C Rockwell hardness values shall apply only to tubes having a wall thickness of 0. All defective asttm shall be replaced with acceptable items before lot acceptance. Light-drawn bending temper is used only when a tube of some stiffness but yet capable of being bent is needed.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? This list may include either current or astk standards.

Ten alloys are speci? Standard Specification for Ferromolybdenum.

  2005 CHEVROLET MALIBU MANUAL PDF

This list is incomplete astk you can help by expanding it. When, in the case where subsequent testing by the purchaser establishes that the material does not meet these requirements, then the tubes shall be subject to rejection.

Copper plus sum of all named elements shall be A Alloy Designations of Speci? When there is a need for light-drawn or hard-drawn tempers these are to be supplied as agreed upon between the manufacturer and the purchaser.

ASTM B无缝黄铜管_百度文库

Former soft anneal soft anneal light anneal light anneal soft anneal soft anneal light anneal light anneal soft anneal soft anneal up to 0. Any evidence of leakage shall be cause for rejection. Screening and resubmittal of samples from rejected lots for visual and dimensional examination is acceptable.

Rockwell hardness values shall apply only to tubes having a wall thickness of 0. Retrieved August 29, Incomplete lists from February Use equipment for the detection and removal of mercury vapor. Rockwell hardness tests shall be made on the inside surface of the tube.

Grossman the Grossman method. The purchaser shall have the right to perform any of the inspections or tests set forth when such inspections and tests are deemed necessary to assure that the material conforms to prescribed requirements.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Preparation for Delivery S4. Views Read Edit View history. Standard Tube Size, inch Up to and including 3? Current edition approved Oct. C Although no minimum grain size is speci?

ASTM B153 – 11(2017)

The test method used shall provide for easy visual detection of any leakage, such as by immersion of the tube under water or by the pressure differential method.

  ASTM A355 PDF

Limits for unnamed elements are to be established by agreement between manufacturer or supplier bb153 purchaser. Standard Specification for Silicomanganese.

Alternatively, if the manufacturer uses speed-insensitive eddy-current units that are equipped so that a fraction of the maximum unbalance signal is able to be selected, the following percent maximum unbalance signals shall be used. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

B — 02 Standard Speci? Except as otherwise speci? The tension test for other sizes of tubes need not be made except when indicated by the purchaser at the astmm of placing the order.

For these tubes, the mercurous nitrate test shall be required and nondestructive testing shall not be required. C on tube sizes greater than 5 in. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Standard designations usually consist of a letter prefix and a sequentially assigned number. Tubes for Voice and Pneumatic Service S5. Prefix letters correspond to the following subjects:. Wear rubber gloves when conducting the test. A withdrawn standard has been discontinued by its sponsoring committee.

A number in parentheses indicates the year of last reapproval.