ANILAM 1100M PDF

I have an anilam that quit working. Will the drive motors from the anilam work with a mach 3 system. And where does a person find a. Hello, Out Anilam m 2 axis system is giving us no video and the computer will not boot. Does anyone know how to repair the system?. Anilam is the company that makes the control. I run a Sharp knee mill with a Aniliam M control. I’m not familiar with the M or sure what.

Author: Arakora Dougar
Country: Spain
Language: English (Spanish)
Genre: Music
Published (Last): 8 April 2006
Pages: 467
PDF File Size: 10.65 Mb
ePub File Size: 13.26 Mb
ISBN: 504-9-47094-941-6
Downloads: 62281
Price: Free* [*Free Regsitration Required]
Uploader: Zuluzil

Continue doing the same process until you determine the cable or cables causing the problem. The 5VDC to power the encoders or scales comes ailam the computer power supply. Please repair as necessary and recheck if everything now works correctly.

What is meant by “Anilam M conversational control”? I would then remove the cpu and flash memory board, and VGA board.

Chapter 5 Servo Card Alignment 1. It’s an easy control to learn and quick to program. Press the F8 key 3 times in a row. Check from P to P and push the reset button.

The password is Y The following are the steps as to where to find the section on changing Buffer size.

To check the computers’ com 2 port do the following: The following drawing is the PC mechanical drawing Part s: Pull out the Emergency Stop switch and press the reset button.

Anila the mill I use, there are lots of canned cycles where you fill in the blanks. This applies to my third option Mach 3, which is also pretty much a roll your own venture. I also visited websites of the various manufacturers of components, e.

  CLOB X SHAMPOO BULA PDF

On newer versions of software you might not see these messages any more.

Controller & Computer Solutions > Anilam m software

The servo turn on circuit comes from the motion control board Part s. Hi JT; It is conversational but it says it can be toggled over to g-code. The following describes the part numbers that are silk screened on the board with the amount of potentiometers mounted on the board.

Press the F1 key.

The time now is This can be cause by the rapid gain not being set properly. You can call Anilam and talk to Jerry in their customer service department. Press the Enter key. Turn anjlam VAC power off and remove this cable from the distribution board. Signal gain not set properly. The software and firmware MUST match! If the voltages are correct with the cable removed, turn the power back off and reconnect the cable. Anilaj you do not have this cable you must add a 12 gauge or 14 gauge stranded wire between cabinets.

Not Enough Memory To Run: There are no gibs to set but any extreme changes will.

Series trouble shooting guide

Turn this potentiometer until you obtain the correct signal setting. For a 2 axis double box or 3 axis system the 5VDC comes from the power supply which is under the distribution board. We want to next check the motor cable that is screwed into the servo box for the axis that caused the fault lights ailam come on.

If the problem remains do 1100, following: I am sure others out there may be able to give you further advise.

Anilam 1100M Programming Manual CNC Three Axis

Check all axis the same way. Hi John, Thanks a lot, I will be contacting him tomorrow. The video shows you how to do it but doesn’t anilsm to leave it that way. I’m guessing it’s an older version or a version with less features I know the M control comes with more features. Gibs to tight or mechanical anilamm. On the drive card there is a small RED Fault light.

  ISO 4427-2 PDF

If you can’t find it just send me a PM and I will respond when I get home.

The test should come back with a passed message after sending and receiving information to itself. Now that you know 1100mm the default rapid speeds are exit from this menu by pressing the F10 key multiple times until you exit to the main menu. Look at the video a couple of times and take the manual to the machine and start programing.

Turn on the main disconnect switch. Upgrade Hi, I have not heard for anyone doing this. In a particular program you have 2 subprograms with the same name. We have seen if you tap on this power supply the distribution board will reset.

Finally the computer responded and only a soft reset occurred which causes both the computer and the distribution board to get back in sync. This message means the control sent a signal out of the motion board but did not see any counts coming back in.

Did the voltage now come back?