ADC0808CCN DATASHEET PDF

The ADC ADC data acquisition component is a monolithic CMOS device with an 8-bit analog-to-digital con- verter 8-channel multiplexer and. ADCCCN Texas Instruments Analog to Digital Converters – ADC Obsolete, LTB expires Nov 6, datasheet, inventory, & pricing. ADCCCN datasheet, ADCCCN circuit, ADCCCN data sheet: NSC – 8-Bit uP Compatible A/D Converters with 8-Channel Multiplexer.

Author: Bazil Zulugis
Country: Great Britain
Language: English (Spanish)
Genre: Automotive
Published (Last): 23 September 2018
Pages: 360
PDF File Size: 11.8 Mb
ePub File Size: 8.37 Mb
ISBN: 535-7-20083-716-7
Downloads: 26386
Price: Free* [*Free Regsitration Required]
Uploader: Akikasa

SPI Module of Arduino. The default step size is These three bits have to be set as shown in the table below to access the respective analog channel.

IC ADC0808

Or even to use as a standalone ADC module. Start conversion; input pin; a low to high pulse is given.

TL — Programmable Reference Voltage. Has to be given clock signals 0V-5V 20Mhz approx.

This pin is should be temporarily made high to select ADC channel. Powers the IC typically with 5V. This is an input pin which is made high to start conversion.

What is Web Browser. These 7 pins are the input pins for Analog voltage sensor.

National Semiconductor

Digital output bit 4. Step size is the change in analog input to cause a unit change in the output of ADC. The right input analog voltage can be given to pins from IN1 to IN7, but the IC can read the voltage of only one channel at a time.

  DATASHEET XR 2206 PDF

End of conversion; output pin; goes low when the conversion is over. Clock input; to provide external adc008ccn. That is for every increase of Has to be made high to get output on output pins.

Arduino based GPS receiver.

The obtained value is 2. Output 2 -1 to 2 Choosing Datassheet For Robots. In the above circuit I have used a potentiometer to feed in a variable voltage of 0V to 5V to the IN1 pin and the present Voltage is read using a voltmeter. This is an output pin which goes high once the conversion is over. It is a pin Eight channel 8-bit ADC module.

Connect to ground of the circuit. This high-density System-in-Package SiP integrates controller, power switches, and support components.

ADC Technical Data

Hence, if you are looking for a ADC module with a decent resolution of 8-bit that could measure up to 8 channels then this IC adc0808ccj for you. End of Conversion EOC. The ADC needs some specific control signals for its operations like start conversion and bring data to output pins. Vref is connected to ground normally. Since the ADC Addc0808ccn can measure up to eight Analog voltage and also does not have an internal clock slightly requires more components to make it work compared to its predecessor ADC Once the channel is set it should be enabled by making the Address latch enabled ALE pin to go high momentarily.

  ALZEYER WOCHENBLATT PDF

ADC is an 8 bit analog to digital converter with eight input analog channels, i. The input which is to be converted to digital form can be selected by using three address lines. Output digital pins which gives the result of the ADC conversion. Interface SD Card with Arduino.

Skip to main content. These three pins are used to select the channel. Interface GPS with Arduino. Analog Channel 1 to 5. As you can see in the image the voltage value is 2. The step size is decided based on set reference value. Submitted by admin on 13 October Input pin; a low to high pulse brings data to output pins from vatasheet internal registers at end of conversion.

When datawheet conversion is complete the EOC pins goes low to indicate the end of conversion and data ready to be picked up. Choosing Battery for Robots. Virgin Galactic — Commercial Space Flight.