I’ve found the installation manual (for my reference), but the D is giving me the most headaches at the moment. If someone can e-mail. Moblie phone manual details for FCC ID 2AL4OSSB made by SSB Trading Inc.. Document Includes User Manual manual. Manual or automatic transmission selection. Note: In the case of D, power and ground must be hardwired to the vehicle – power and.

Author: Goshicage Kazikora
Country: Albania
Language: English (Spanish)
Genre: Medical
Published (Last): 4 November 2005
Pages: 435
PDF File Size: 17.88 Mb
ePub File Size: 20.20 Mb
ISBN: 245-2-87484-704-2
Downloads: 18472
Price: Free* [*Free Regsitration Required]
Uploader: Duhn

Product Limited Warranty A. This means you can connect the signal pin to a Arduino digital input pin, but you need to connect it to a pull up resistor so you get a constant value. To print the manual completely, nanual, download it.

If only the latter works and gives This is the “manual”: Product Limited Warranty Acer Netxus Incorporated ANI warrants its product to be free from 508e in materials and workmanship, under normal use and service, for the following lengths of time from the date of purchase from ANI or its Authorized Resellers. That means it’s grounding, right?

Sharp Carousel R-508D Manuals

Open-collector or open-drain, same thing outputs are nice and flexible like this you can wire several of them together to one pull-up resistor to make a hard-wired Mankal gate too. Table Of Contents Table of Contents 0. Page of 13 Go. Collision indicator It will flash when Mbps segment network collision occurs. Thanks for your help! Collision indicator It will flash when 10 Mbps segment network collision manua.


Now I’m starting to see what the term “pull-up resistor” actually means!

Comments to this Manuals Your Name. This company makes no representations or warranties, either expressed. Table of Contents 0. MarkT Brattain Member Posts: If both generate an output then take note of the voltages involved. Got it, continue to print.

Sharp Carousel RD Manuals

With a 10K resistor connected between the output and the 16V rail sorry, no 5V available right nowit reads 15V at the output when inactive, but drops to zero when triggered. Acer 8-port dual-speed ethernet hub user’s manual alhds 32 pages.

You can use the uplink port of the Ethernet hub to uplink to normal port of ALHd to upgrade some key network user from 10Mbps to Mbps 5508d connect to ALHd and leave the others connect to the Ethernet hub segment. Quick Installation Guide 1. I took a few electronics courses back in college, but have forgotten most of it. Further, this company reserves. How would I sense that, and is it OK to connect that resistor directly to the Arduino’s 5V power even though this runs on car 12V?

The blue wire is “alarm” – someone’s entered the smaller alarm perimeter. Measure the output voltages with nothing connected, and then again with 10k resistor from output to 5V. A Communications Company of Acer Enter text mabual picture: Please orient the cable correctly and push it into the connector until you hear a click. Page 5 You can use the uplink port of the Ethernet hub to uplink to normal port of ALHd to upgrade some key network manusl from 10Mbps to Mbps by connect to ALHd and leave the others connect to the Ethernet hub segment.


It’s a 12V circuit, it has two outputs which I’d like to sense. Check the PDF Manual: Hmm, rather unclear that document and my neck now aches I think it might mean the outputs are open-collector capable of mA sink. I didn’t want to pass that voltage into the Arduino and fry it.

But I found good input to the initial problem under: Don’t have an account? Is there something I can read online to get a better understanding?

Great, thanks so much for your help! I’m also trying to use this sensor, but confused about what the blue and green wires do. Led Indicators And Ports Description 2. When the alarm is triggered the signal pin is connected to ground.

Don’t show me this message again. Eventually I realized that the signal pins are left floating when the alarm is not triggered.

When I first tried hooking this up to my Arduino I was worried about the sensor running on manuap. Table of Contents Add to my manuals Add. Without a resistor, it measures 0V when inactive, about 6. However I’d suggest it would be best to measure. By pressing ‘print’ button you will print only current page.

DEI Viper 508d Manual and Advice?

Acer dual-speed ethernet hub user’s guide alhds 32 pages. I know thread is old. If 12V you’d need a level shifting circuit such as resistor divider.