4226T MANUAL PDF

3com SuperStack 3 T Pdf User Manuals. View online or download 3com SuperStack 3 T Getting Started Manual, Datasheet. User manual for the device 3Com SUPERSTACK T. Online user manual database. Get 3Com SUPERSTACK T Switch User Manual. Get all 3Com manuals!.

Author: Mazujas Nebei
Country: Ghana
Language: English (Spanish)
Genre: Finance
Published (Last): 22 October 2016
Pages: 167
PDF File Size: 11.59 Mb
ePub File Size: 9.11 Mb
ISBN: 232-8-79073-598-6
Downloads: 23993
Price: Free* [*Free Regsitration Required]
Uploader: Gardataxe

The production process for making the manial has a reduced AOX level adsorbable organic halogen resulting in elemental chlorine-free paper. Using the Web Interface 1 Power-up the Switch.

Setting Up Snmp Management Switch t 3c This manual is printed on paper that comes from sustainable, managed European forests. MDI port, you need to use a standard straight-through cable.

Only connect RJ dataconnectors, network telephony systems, or network telephones to thesesockets. Documentation supplied with the terminal emulation software.

3com SuperStack 3 T Manuals

There is also an explanation of IPaddressing. Table Of Contents You will only need to enable them ifyou have changed your browser settings. Use the following sequence of steps to power-up the Switch.

Choosing The Correct Cables You must read the following safety information carefully before youinstall or remove the unit. Switch g 3c The default state for manaul ports is auto-negotiation enabled, where speed, duplex and flow control modes are negotiated. Setting Up Web Interface Management If the login prompt does not display immediately, press Return a few times until it starts.

  LIBRO EL OTRO SENDERO HERNANDO DE SOTO PDF

3Com 4226T Switch User Manual

mahual Figure 9 Connecting a workstation to the Switch via a front panel portTo connect the cable: No part of this documentation may bereproduced in any form or by any means or used to make any derivative work such as translation,transformation, or adaptation without written permission from 3Com Technologies. Either shielded or unshielded data cables with shielded or unshield.

Configuring Workstation With Ip Information The initial set up of your Switch is now complete and the Switch is readyfor you to set up your chosen management method. If you are placing Switch units one on top of the other, you must use theself-adhesive rubber pads supplied.

3Com SUPERSTACK 4226T user manual

Cli Management Over The Network The topics covered are: X where X is a number between 1 and with a subnet mask of Make a note of the Network IP Address. Switch Family – Front View Detail 4226t OffThe Switch is not receiving power. However, to make full use of the features offered by the Switch, and to change and monitor the 422t6 it works, you have to access the management software that resides on the Switch.

Upport For Your Product No part of this documentation may be reproduced in any form or by any means or used to make any derivative work such as translation, Campus Drive transformation, or adaptation without written permission from 3Com Technologies. Redundant Power To protect against internal power supply failure, you can use this socket System Soc. Either shielded or unshielded data cables with shielded or unshield Summary of the content on the page No.

  ELOPS SAURUS PDF

For example, you can use the 3Com Network Supervisor Switch page Air-flow is not restricted around the Switch or through the vents in the side of the Switch.

See 3Com recommends that you use Category 5 twisted pair cable — the maximum segment length for this type of cable is m ft. Switch Family – Rear View Detail Alternatively, auto-negotiation can bedisabled and the flow control setting can be manually configured.

You are now maanual to view the automatically allocated IP information using the command line interface.

3COM SUPERSTACK T GETTING STARTED MANUAL Pdf Download.

If installing the Switch Series unit in a stack with SuperStack II or SuperStack 3 units that are narrower than the Series, the Switch Series unit must be installed below the narrower units. This section applies to the SuperStack 3 Switch G only. The conditions are only maintained ifthe equipment to which it is connected also operates under SELVconditions. Many people prefer to read the documents not on the mannual, but in the printed version. If connecting a modem to the console port of the Switch Series, only use a modem which is suitable for connection to the telecommunications system.